Fonts

Items 1 to 10 of 20 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction
  1. Cobra Single Tap Font

    Cobra Single Tap Font

    Price: AU$159.95

    Features:
    - Single Tap Font
    - Glycol Loop for use with glycol or water chiller
    - Made from cast brass with chrome plating
    -5/8 inch female sockets for attaching shanks

    To attach a tap to these fonts you will either need the Stainless Short Shank witout barb or the KingLok font adaptor and KingLok tap shank adaptor. It is also recommended to use the thick black silicone washers to seal the shank/kinglok into the font.

    The inlets to these fonts are 8mm OD stainless tube out the base of the font, you can use the 8mm compression fittings to 6mm barb to fit 4-6mm ID lines if needed.

    note: does not include taps

    Learn More
  2. T-Bar Flooded Font - Double Tap

    T-Bar Flooded Font - Double Tap

    Price: AU$599.00

    These flooded fonts are just what you need to setup your bar or pub. When glycol chilled these fonts will freeze up with a layer of ice meaning you will be dispensing bitterly cold beer even on those stinking hot days.

    These fonts are 430mm tall, the two furthest taps are 225mm apart on the double and triple tap models. They are made of 304 stainless and chrome plated. A 60mm hole in the bench/bar is required and they secure with a large nut on the underside. It is recommended to have some drainage at the base of the font to collect condensation.

    The font does not include taps or KingLok (Snaplok, FatLock ect) fittings. The recommended KingLok fittings to use with this font are the KingLok female x 5/8 male + 8 John Guest Push In.

    Learn More
  3. T-Bar Flooded Font - Single Tap

    T-Bar Flooded Font - Single Tap

    Price: AU$499.95

    These flooded fonts are just what you need to setup your bar or pub. When glycol chilled these fonts will freeze up with a layer of ice meaning you will be dispensing bitterly cold beer even on those stinking hot days.

    These fonts are 430mm tall, the two furthest taps are 225mm apart on the double and triple tap models. They are made of 304 stainless and chrome plated. A 60mm hole in the bench/bar is required and they secure with a large nut on the underside. It is recommended to have some drainage at the base of the font to collect condensation.

    The font does not include taps or KingLok (Snaplok, FatLock ect) fittings. The recommended KingLok fittings to use with this font are the KingLok female x 5/8 male + 8 John Guest Push In.

    Learn More
  4. SL6 Washer

    SL6 Washer

    Price: AU$1.10

    SL6 Washer This washer is a replacement seal for the female KingLok fittings. They are also the best seals to use when sealing the angle barb tail to the back of the KingLok 3/4" female in the modular or similar fonts. 24.2mm x H4.40mm x 12.40mm Learn More
  5. Kinglok Female x 5/8 Male + 8mm Push In (Flooded Font Adaptor)

    Kinglok Female x 5/8 Male + 8mm Push In (Flooded Font Adaptor)

    Price: AU$34.95

    The KingLok adaptors/quick disconnects are compatible with Andale (Snaplok), Lancer Pacific (Fatlock) and other brands of draft beer quick lock fittings that are often seen in commercial pubs and bars.

    This fitting is designed to work with our fully flooded T-Bar fonts.

    These KingLok couplers are designed to be a dry break so when you disconnect the male side the flow is cut off.


    Learn More
  6. 5/8 Inch Lock Nut

    5/8 Inch Lock Nut

    Price: AU$1.95

    5/8 Inch Lock Nut

    This nut will suit the 5/8 inch thread found on most tap shanks. They are typically used to secure the tap shank to a font or through the wall of an esky or fridge wall.

    Learn More
  7. Decal Holder 82mm Chrome Plated Plastic

    Decal Holder 82mm Chrome Plated Plastic

    Price: AU$13.95

    These decal holders are literally made to support your brand name. Due to the novel two piece design the sliding base moves up and down allowing the decal holder to be fitted to ANY TAP design so there is no issues with incompatibility. For attachment the sliding base can be removed with a Philips head screwdriver so there is no need to remove the tap from the front to fit the decal, it simply fits over the tap or shank and you do up the screws on the underside. The holder will support a sticker or decal up to 82mm in diameter. Note: tap, font and screwdriver are not included

    Learn More
  8. Decal Holder 82mm Copper Plated Plastic

    Decal Holder 82mm Copper Plated Plastic

    Price: AU$16.95

    These Copper plated decal holders are literally made to support your brand name. Due to the novel two piece design the sliding base moves up and down allowing the decal holder to be fitted to ANY TAP design so there is no issues with incompatibility. For attachment the sliding base can be removed with a Philips head screwdriver so there is no need to remove the tap from the front to fit the decal, it simply fits over the tap or shank and you do up the screws on the underside. The holder will support a sticker or decal up to 82mm in diameter. Note: tap, font and screwdriver are not included

    Learn More
  9. Decal Holder 73mm Copper Plated Plastic

    Decal Holder 73mm Copper Plated Plastic

    Price: AU$16.95

    These Copper plated decal holders are literally made to support your brand name. Due to the novel two piece design the sliding base moves up and down allowing the decal holder to be fitted to ANY TAP design so there is no issues with incompatibility. For attachment the sliding base can be removed with a Philips head screwdriver so there is no need to remove the tap from the front to fit the decal, it simply fits over the tap or shank and you do up the screws on the underside. The holder will support a sticker or decal up to 73mm in diameter. Note: tap, font and screwdriver are not included

    Learn More
  10. T-Bar Flooded Font - Triple Tap

    T-Bar Flooded Font - Triple Tap

    Price: AU$649.00

    These flooded fonts are just what you need to setup your bar or pub. When glycol chilled these fonts will freeze up with a layer of ice meaning you will be dispensing bitterly cold beer even on those stinking hot days.

    These fonts are 430mm tall, the two furthest taps are 225mm apart on the double and triple tap models. They are made of 304 stainless and chrome plated. A 60mm hole in the bench/bar is required and they secure with a large nut on the underside. It is recommended to have some drainage at the base of the font to collect condensation.

    The font does not include taps or KingLok (Snaplok, FatLock ect) fittings. The recommended KingLok fittings to use with this font are the KingLok female x 5/8 male + 8 John Guest Push In.

    Learn More

Items 1 to 10 of 20 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction